![]() Steps to program using nRF Connect programmer are described here. Start at this step: "Open nRF Connect software suite. ![]() Refer to M1-N1 data-sheet for Pin description to power M1-N1.įirmware can be now flashed using nRF Connect programmer OR nRF command line. Be sure to assert high PWR_ON pin of M1-N1, to enable the power supply.After finishing the wiring, plug ST-Link-V2 USB dongle to PC.Power M1-N1 externally via TC or LPC connector. NOTE: Do not connect Vcc pins from USB Dongle to M1-N1. Note: The pin visible through the slot is Pin 5. Connect M1-N1 to ST-Link V2 USB Dongleĭisconnect STLINKV2 USB dongle from PC before connecting to M1-N1 Tag-Connect Now STLinkV2 is properly converted to J-Link. Ensure to close the STLinkFlasher programmer command line utility by selecting ` Quit`.ĭevice Manager should now show ST-Link V2 USB dongle as `J-Link driver` as shown in the picture below.Ģ. Install STLinkReflash_modified.exe by running as Administrator, and follow the steps to "Upgrade to J-Link" as described above. Use the attached modified STLink_Reflash.NOTE: You may encounter issues when using STLink Reflash utility from SEGGGER.This is a command line utility to convert ST-LINK on-board version into a J-Link-OB by replacing the firmware. Download and Install the modified SEGGER STLink_Reflash utility.Download and install SEGGER J-Link software package.Download and Install USB driver (STSW-LINK009) for ST-LINK/V2 from SEGGER.Follow the procedure from SEGGER for Converting ST-LINK On-Board Into a J-Link. ![]() ![]() Plug STLINKV2 dongle to a Windows PC. It will be shown in the Windows Device Manager as shown below: It is not about using STMicroelectronics ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Information about ST-LINK/V2 can be found here and here ![]() Note: This article details using ST-Link-Compatible Programmer & Emulator / Debugging USB dongle to program Nordic nRF9160. It also withstands voltages of up to 2500 VRMS.The following article provides a means to program Nordic nRF9160 based SigCell M1-N1 using ST-Link-Compatible Programmer & Emulator / Debugging USB dongle. In addition to providing the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL features digital isolation between the PC and the target application board. It supports all the features of ST-LINK plus some additional featuresĪt the same price. Installing tools like STM32 Cube Programmer should on-board sufficient drivers for Windows to find and associate with the device. STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil, TASKING, etc, integrated development environments. In Boot mode (BOOT0HIGH/ONE) the System Loader should be a 'STM32 BOOT LOADER' type USB device provided the cabling, wiring and powering of the board design permit. STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop ( STVD) or ST Visual Program ( STVP) software. this is my first try to work with ARM and I bought stm32f103c8t6 that is simple to start with it a few days before i buy a big development board I have a problem in installing usb driver on windows 10 for stm32f103c8t6 I have STM32CubeMX and already installed stm32f1 package but. The single wire interface module ( SWIM) and JTAG and Serial Wire Debugging ( SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board. The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |